Product Code
Product description
Product Picture
Info
Product Position
GLAZING SUPPORT TRIM / INTERNAL CLADDING
this clips onto the aluminium ridge body and is the internal cladding and support for the glass / polycarbonate (this only runs from glazing bar to glazing bar
ALUMINIUM RIDGE BODY
central piece of the conservatory roof. This supports all the glazing bars and attaches to the host wall
RIDGE BODY TOP CAPPING
This is seated on the top of the ridge body as a cladding allowing weather proofing.
RIDGE UNDER CLADDING
located / clipped to the underside of the main ridge body as an internal cover
RAIN BAFFLE
This connects to the upper lip of the aluminium ridge body and creates a seal with the glass to ensure the glazing is made water tight
ALUMINIUM RIDGE HANGER
used on the house wall to secure the ridge body in place.
CONSERVAFLASH RIDGE SADDLE FLASHING
Used at the rear/house wall side of the roof to enable a weatherproof seal without the need for lead.
RIDGE HUB END
secured to the main ridge body to allow the glazing bars to connect (acts as a die cast end)
RIDGE EXTERNAL REDIUS END VICTORIAN
secured to the main ridge body to allow the glazing bars to connect (acts as a die cast end)
VICTORIAN INTERNAL RADIUS END
Locates under the ridge end hub once the glazing bars are in position as a internal cover trim.
RIDGE HUB END
secured to the main ridge body to allow the glazing bars to connect (acts as a die cast end)
RIDGE EXTERNAL REDIUS END GEORGIAN
Located at the finial point end of the ridge and is used to cover the hub end weathering tray
GEORGIAN INTERNAL RADIUS END
Locates under the ridge end hub once the glazing bars are in position as a internal cover trim. This is for a roof with a central glazing bar located on the front elevation
GEORGIAN INTERNAL RADIUS END
Locates under the ridge end hub once the glazing bars are in position as a internal cover trim. This is for a roof with a central glazing bar located on the front elevation
FINIAL
located on top of the external radius end. This is also an integral part of the self ventilating system used in the u-zone roof
M8X40 BOLTS
Used in conjunction with the ridge gripper
M8 HALF NUT
Used along with the M8 bolts and washers to secure the ridge to the ridge hanger using the ridge hanger gripper
M8 PLAIN WASHER
Used in conjunction with the M8x40 bolts and the ridge gripper. These are used to secure the ridge body to the ridge hanger
RIDGE TO HUB END BOLT
Used to secure the ridge hub end to the main ridge body
M8 LOCK WASHER
Used in conjunction with the M8x40 bolts and the ridge gripper. These are used to secure the ridge body to the ridge hanger
VICTORIAN HUB END WEATHERING TRAY
Locates on to the top of the ridge end hub once the glazing bars are in position as a weather proofing system
GEORGIAN HUB END WEATHERING TRAY (WITH CENTRE BAR)
Locates on to the top of the ridge end hub once the glazing bars are in position as a weather proofing system. This is for a roof with a central glazing bar located on the front elevation
GEORGIAN HUB END WEATHERING TRAY (WITHOUT CENTRE BAR)
Locates on to the top of the ridge end hub once the glazing bars are in position as a weather proofing system. This is for a roof without a central glazing bar located on the front elevation
FAN MOUNTING BRACKET
Used to secure a fan to the ridge body (if required)
T-BOLT
This (as in the classic system) secures the ridge top cap to the ridge body
T-BOLT SLIDER
used to secure the T-bolt once the ridge body top cap is pulled down.
SPIRIT LEVEL
to enable the fitter to ensure the ridge/wallplate is level
RIDGE HANGER GRIPPER
Used in conjunction with the aluminium ridge hanger. This is used to secure the ridge body to the ridge hanger using two M8 bolts and washers
CRESTING ADAPTOR
This allows the cresting section to be connected to the finial